I have made a fuel and spark map for my b18ft with a view to running 2 bar boost. The car dosnt run at the mo so I'm only letting the engine idle, but do these maps look good enough as a starting point?
I have made a fuel and spark map for my b18ft with a view to running 2 bar boost. The car dosnt run at the mo so I'm only letting the engine idle, but do these maps look good enough as a starting point?
Does the b18ft run that high of a idle advance?
You could keep the off boost ignition a lot higher as that isnt affected by the boost map.
Other then that the ign. Table looks good on the conservative side.
Also i think it would be better to scale in alot more off boost bins as that is where you'll drive daily. Above 200 kpa you'll rise rapidly trough them to 300kpa anyway so not much use to have that much bins.
Try to find a 300kpa table on the net as example and copy the bin layout (Y)
Cheers matey had a little play how about this one.
Just realised where it says 289 now says 190.
You want a lot more vac advance than that and less around the idle (40kpa, 1000rpm). Maybe 10-12 degrees, not 22. Timing at WOT is going to depend a lot on your setup but it looks acceptable. Maybe knock a couple degrees off that for initial testing. B18ft doesn't like a lot of timing at WOT.
I wouldn't get too hung up on 2 bar either, they really don't breath these engines even with the NA cam. I bet you won't see much more after 1.6 bar
im getting confused now
so around idle it wants to be around 10 then can increase as revs and kpa increase but when i reach around 100kpa and 3000 rpm i want to drop that advance down?
has anyone got a decent table i can have a look at i have a few here but none seem right
Well, to understand what's going on with the map the first thing to do is find out what's going on inside the engine.
im trying to see what the stock internals will take im sure its more than my set up can manage tho
ok still trying to understand this, i need around 10 for idle then i can advance as the kpa and rpm increases until the rpm reaches 4k (turbo kicks in) then i have to start retarding and when the kpa reaches 100 start retarding. but in the areas that i prob wont reach in the map like 40kpa 7000rpm i can really advance? and likewise 500rpm 300kpa where i wont reach i can advance?
Done some more playing
Better, but you have more timing at 75kpa than you do at 0kpa at certain rpm's, which doesn't make sense. You can go to 30 deg or more at low kpa's and higher rpm.
It's not about finding the limits of the internals. Whats the point in running 2 bar if it makes no more power than it does at 1.6. From experience they just don't make much more than 230hp without a fight. Hopefully in a week or so well be able to try Lee Wadmoors B18FT engine with it's new cam from Markey mark. There was some problems with valve bounce at high RPM, hopefully thats rectified now and we can continue the mapping. It was showing good power at low boost so fingers crossed.
that was the head and cam that was accidently made for me
ok i will advance those areas more still trying to get my head round all this ecu lark
Right I have been playing with the map on the 3d table and from about 2000rpm now it has a lot of advance and slowly tapers off as the Loa increases. I'll post a pix later to see what ya think.
Chris I have a rsi cam and it spiked to 2bar accidently when the wastegate stuck and it seemed quicker until a boost hose popped off
I don't want to reach the limit of standard internals but I would like what power I can get which is why I will be getting it properly mapped when I have sorted the rest of it out.
Had another play this evening taking into account what everyone has said. How does this one look then?
looking better, however at max torgue the timing would be least. so after 4000rpm timing could go up a bit.
Just something I've noticed Gary. With the ignition tables I've got with the C1J the values go up with rev's not down. I would think it is the same with the volvo lump.
example of a very early base map on mine
so at 8000rpm 300kpa max boost theres 26degrees advance seems a lot
scoff reckons 10 deg at WOT so was going with that. Also its slightly higher comp and a flat head so dont know if that makes a difference but think it might not be able to have as much as the c1j.
I want something looking good but quite safe at the min as its not driveable so cant test but will up it when i can
Thats the one mate
I must admit i did talk to Waddie about opening the exhaust port alittle as this looks the restrictive part of the head but he decided to leave as to see what difference the cam made
Heads now fitted with double valve springs fitted so should be sorted now, engineers did admit old springs were way too soft for cam profile
Can't wait to see the power it will make. Hoping I will get a fair bit, will be good to see how much a pretty much standard engine can make.
Maybe something to look into at some point, but saying that if I did want more I'd prob go f7p and o2m
nope would have thought a lot of it is down to the inlet One side n exhaust otherside tho.
The engine will be powerful enough, make car light enough and it'll go well
Got to think of reliability too, these are built like battle ships very strong bottom ends
Ask Romil and Logg what my B18FT van went like at 160bhp when we had alittle race on way to Nat Day this year
The b18ft can be done on a tighter budget. All I have is a rsi cam and a big blower. The ms cost 250quid if I were to go straight to where I am now I reckon I could have done it for 1k. Hopefully soon il be able to do some power runs to see how much easy power can be had
I was pleasantly surprised by the thickness of the con rods
Right since sorting the timing the engine has now developed a miss fire over 3k. I have cleaned the plugs and its not that, I'm sure its down to the timing as when I sorted it it got knocked back by about 10degrees over the whole rev range. How much can I advance the timing in low load areas?
I don't think I said 10 deg at WOT ? I wouldn't have offered any exact suggestions for WOT. You also can't compare B18FT with C1J, the timing map requirements are nothing like. C1J needs more advance just about everywhere.
As the guys say you have the top half of the table arse about face. With the B18FT you dont want a lot of timing at WOT where peak torque happens. You need to be feeding it back in as revs rise though. I'd be starting very safe where peak torque happens and initially no more than 16deg@ 6000rpm / 230kpa. Work from there. You need to look at and absorb some other turbo timing maps to get a feel for what the engine wants. I wouldn't put too much stock in the b18ft timing map that floats around on the web, it doesn't look right to me
You can put more timing in at vacuum above 3000rpm say. Beware that moving the timing has an impact on how it fuels in those areas too, so pulling 10 deg probably made it go richer in those areas. Maybe it's bogging down now.
Just as a random aside, I finally got to tuning Lee Wadmores B18FT GTT last week with it's headwork and custom cam from Markey mark. I was very impressed, it went as well as I expected it to with a real cam. 203hp at 13.5psi and 224hp at about 17psi. He has a 0.86 T28. His actuator was knackered so we could not test with more boost but it goes to show how much better these engines will go with a performance cam.
Cheers Chris I will have a look and re tune my map tomorrow and il post it up to see what ya think. I too have a t28 with a .86 rear but only have a rsi cam. Will be good to see what the headwork has done.
Are you road-mapping, on the dyno, using a steth', etc? Surely you're not just entering the numbers willy nilly?
As a good r.o.t, try not to have too large a value variation between cells. 3 is about the most you want to go on the scaling you have.
Can you source an o.e ign' map? At least you'll have a good starting point, then tweak accordingly from there.
Mart I haves had a look for std ign map but no joy il keep looking tho. Atm its just idling an revving as it can't drive so I'm just getting it to rev nice. I will be tuning it on the rd until I can get it to someone like Chris. I have a knock monitor but want to test it. Is there any way I can test it with out making the engine nock?
the rsi cam seems good i can only compare to the ep cam and to me it feels better bit more power but who knows could be making less
Yes, head work is to accept the cam. It's machined, double sprung etc.
Never had the 'e' cam to campare matey but don't think the 'e' is much more wild than the 'ep'.
How about this then?
Looks lots better mate!
Too much at 4000rpm for my liking though. You need to be very safe at peak torque with these engines. 10-12 deg maybe then progress from there.
Well lets say 10 deg at about 230kpa, it can ramp up as load decreases.
Excuse the ignorence but is this what ya ment chris?
Looking best so far Better to start safe than sorry.