-
Look-Out
O.E c1j build
Right, seing as my ph1 project is nearing completion i thought id better get my ass in gear and get a motor sorted, seeing as the old engine ended up going in the cup car leaving the ph1 motorless !
Ive got so many spares id thought id combine the best bits i have a build up a nice little tidy lump, Il write on here with pics as i go incase it helps anyone else wanting to do the same thing
Im quite lucky i have all the kit at my disposal at work which makes life alot easier when it comes to cleaning up / checking parts .
Right, big thanks to Big Steve, the block and crank came from a low mileage R11T. Block was acid dipped at work and throughly cleaned / flushed. blown through, threads chased etc. The crank was standard and just needed a slight polish in the lathe and it was good to go. I picked four of my best liners, measured them up on the CMM at work and gave them a quick hone. Again i found four decent pistons and fitted new rings. New big ends, mains and thrusts are in the post. I have cleaned up all the other internals / refurbed the oil pump etc etc. All the top end is already built up, ready to bolt on....Il take pics over the weekend as i go
In no particular order, only got afew pics atm
https://www.rtoc.org/boards/album.php...pictureid=4174
https://www.rtoc.org/boards/album.php...pictureid=4176
https://www.rtoc.org/boards/album.php...pictureid=4177
https://www.rtoc.org/boards/album.php...pictureid=4179
https://www.rtoc.org/boards/album.php...pictureid=4178
-
Re: O.E c1j build
That block looks spot on Kris!!
Think I may dip my block when I rebuild the 11?
-
Non-member
Re: O.E c1j build
Looking good mate, looking very good
-
Non-member
Re: O.E c1j build
Good work mate! Will be a nice standard engine when done
-
Look-Out
Re: O.E c1j build
Yeah steve, it came up mint. A nice base to work from and paint etc
Few more pics here
https://www.rtoc.org/boards/album.php...pictureid=4182
https://www.rtoc.org/boards/album.php...pictureid=4181
Shells came today, so il start putting it back together this weekend
Last edited by Kris M; 06-01-2012 at 19:09.
-
Look-Out
Re: O.E c1j build
Got the crank in earlier, turns freely with correct end float which is a god start !
Started messing around with the liners / protrusion etc but il carry on with that tmrw evening.
https://www.rtoc.org/boards/album.php...pictureid=4196
https://www.rtoc.org/boards/album.php...pictureid=4198
https://www.rtoc.org/boards/album.php...pictureid=4197
-
Non-member
Re: O.E c1j build
looks awesome, satin black block would have been more OE tho
-
Moderator
South East Regional Rep
Re: O.E c1j build
Very impressive
-
East Midlands Regional Rep
-
Look-Out
Re: O.E c1j build
Gonna have to stick my new liners in now. Two of the ones id refurbed were below the level of the block by a knats! Checked all 4 of the new ones and ive got perfect protrusion on all. Not sure how the old liners could of worn that way, or maybe they were slightly out or tolerence from the factory ?
https://www.rtoc.org/boards/album.php...pictureid=4207
Last edited by Kris M; 09-01-2012 at 23:07.
-
Look-Out
Re: O.E c1j build
Put the new pistons and liners in, in the end. Protrusion was spot on eventually ...Got the cam and timing gear fitted tonight and also got the head on and torqued up
https://www.rtoc.org/boards/album.php?albumid=1486
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules