Results 1 to 20 of 20
  1. #1
    Non-member
    Join Date
    Jul 2012
    Posts
    131
    Post Thanks / Like

    fuel relay wiring

    Hi,dont supppose anyone has the wiring digram of the fuel pump and relay, its circuit digram 20 and also the page that lists the components as i dont have these pages in my haynes manual

  2. #2
    Moderator, Committee Trevhib's Avatar
    Join Date
    Sep 2008
    Location
    Derby
    Posts
    5,829
    Post Thanks / Like

    Re: fuel relay wiring

    I assume it's in here:
    https://www.rtoc.org/files/?path=Tech...ng%20diagrams/

    Various fuel related diagrams/wiring in there but not sure if it covers exactly what you need.

    Plus some info about the relay itself, here and here:
    https://www.rtoc.org/boards/showthread.php?t=19
    https://www.rtoc.org/boards/showthread.php?t=4723

  3. #3
    Committee, South East Regional Rep James5's Avatar
    Join Date
    Aug 2002
    Location
    RH13
    Posts
    6,045
    Post Thanks / Like

    Re: fuel relay wiring

    Fuel Pump relay colours are

    Thick red = Battery +ve
    Thick white = Fuel pump +ve
    Thin black = ground
    Thin yellow = ignition +ve
    Thin brown/grey = tacho

    The relay watches the tacho signal to decide when to switch the pump on and off.

  4. #4
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    What are the colours of the 3 wires to the AEI?

  5. #5
    Super Administrator R5MJH's Avatar
    Join Date
    Feb 2011
    Location
    Down South
    Posts
    3,865
    Post Thanks / Like

    Re: fuel relay wiring

    Quote Originally Posted by Matt Cole View Post
    What are the colours of the 3 wires to the AEI?
    think grey is tacho matt not sure on rest

  6. #6
    Moderator, Committee Trevhib's Avatar
    Join Date
    Sep 2008
    Location
    Derby
    Posts
    5,829
    Post Thanks / Like

    Re: fuel relay wiring

    Matching the list of wire colours in this article (page 2):
    https://www.rtoc.org/boards/showthread.php?t=1666

    With this diagram:
    https://www.rtoc.org/files/Technical%...p%20wiring.jpg

    It looks like, M/V (Brown and Green), N (Black), and Bc (White) come from (or go to) the AEI (on that three pin plug). Are they the three wires you meant?

    M/V is noted as the output from the AEI to the rev counter.

    Is that about right? Difficult to see the diagram properly.

  7. #7
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Cheers Trev. Its the three wires (tacho, ign switched live and earth). Thing is, at the fuel relay the colours are slightly different. The Tacho is grey to the relay but most suggest brown to the AEI? I guess it must split off a different colour to the back of the rev counter.

  8. #8
    Moderator, Committee Trevhib's Avatar
    Join Date
    Sep 2008
    Location
    Derby
    Posts
    5,829
    Post Thanks / Like

    Re: fuel relay wiring

    I dunno mate. In theory it should be possible to wade through the diagrams and follow the wires all the way along their respective routes. Would be easier if printed out I imagine.

  9. #9
    Committee, South East Regional Rep James5's Avatar
    Join Date
    Aug 2002
    Location
    RH13
    Posts
    6,045
    Post Thanks / Like

    Re: fuel relay wiring

    Quote Originally Posted by Matt Cole View Post
    Cheers Trev. Its the three wires (tacho, ign switched live and earth). Thing is, at the fuel relay the colours are slightly different. The Tacho is grey to the relay but most suggest brown to the AEI? I guess it must split off a different colour to the back of the rev counter.

    What you wiring in Matt is this for a C1j Setup or wiring for your adaptronic?

    Grey - Tacho
    GND
    Positive - Yellow

    2pin plug 1 is pink / white this goes to Ign1 on adaptronic

  10. #10
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Quote Originally Posted by James5 View Post
    What you wiring in Matt is this for a C1j Setup or wiring for your adaptronic?

    Grey - Tacho
    GND
    Positive - Yellow

    2pin plug 1 is pink / white this goes to Ign1 on adaptronic
    Yeah it's to wire in the adaptronic. It'd years since I did it. I used a separate relay and connected some of the wiring to the back of the relay. I guess I was only using the thick white to trigger the fuel pump.

  11. #11
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Sorted now. Pump now working. Just need crank pick up to respond then job done!

  12. #12
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Reviving an old thread. Wiring isn't my strong point so guidance appreciated.

    I need to replace the wiring to my fuel pump. I figure the 35 years of use probably wont hold the current i need for my fuel delivery needs. Now, i use a separate relay triggered from my ecu and from memory i 'tapped' into the wiring serving the original fuel relay. Im wondering if i can do away with the original relay completely?

    My main question is, do i just run new wiring from my own relay directly to the pump? Also what size wire would be recommended for maintaining a good voltage?

  13. #13
    Committee, Treasurer, Memberships admin Ian S's Avatar
    Join Date
    Sep 2000
    Location
    Essex
    Posts
    5,832
    Post Thanks / Like

    Re: fuel relay wiring

    Does your new setup sense if the engine is running or not and shuts of the fuel if not?

    Your new pump might be more efficient and use less current than the 1980's one. You could check the specs on them and compare the current requirements.

    Unless the sheath has chaffed or gone brittle, the old wiring should be OK I'd guess but the joins might be corroded.

  14. #14
    Non-member Matty's Avatar
    Join Date
    Aug 2014
    Location
    Longwick, Bucks
    Posts
    513
    Post Thanks / Like

    Re: fuel relay wiring

    I ended up just using some male spades into the original grey relay connector using the red,white, yellow wires, and because I was lazy I took a switched live signal from the radio. I ran these into a relay block, and fitted a standard 4 pin relay. Most are switched ground to the ecu.

    It means the pump is always on, but it doesn't bother me. I started messing about using the starter motor exciter wire as a prime function to get the engine running, and hoped it would switch to the relay after starting, but for some reason the Rev counter signal wasn't good enough to switch the original relay after start up.

  15. #15
    Committee, Treasurer, Memberships admin Ian S's Avatar
    Join Date
    Sep 2000
    Location
    Essex
    Posts
    5,832
    Post Thanks / Like

    Re: fuel relay wiring

    I had a look at the article where I drew out the circuit diagram, but the photo is missing.

    Found this from Scoff it's it's any use:

    Here is the fuel pump pin numbers and wiring for the R5 GTT fuel pump:

    pin 1: fat white = to fuel pump
    pin 2: black = earth
    pin 3: brown = tach input from AEI
    pin 4: not connected
    pin 5: yellow = ignition live
    pin 6: fat red = battery live


    Data taken from Ian Simpsons original article:

    Fuel pump relay module wiring connections.

    PIN 1: Live wire to fuel pump (This is the thick white wire on the white plug that goes to the fuel pump)
    PIN 2: Earth (this can bolt straight to the body)
    PIN 3: Rev Counter (This is the pink wire from the 3 pin plug on the AEI) Split the wire so that it connects to here, the AEI and into the car)
    PIN 4: UNUSED
    PIN 5: Ignition Live
    PIN 6: Battery Live

  16. #16
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    So im now running two pumps, one as a lift pump to my surge tank and a new high pressure pump to the rail. I've purchased new wiring and and new relay. My thoughts are that i leave the lift pump on the original wiring (triggered off the ecu and hacked into the appropriate wires on the original relay plug) and wire in the new relay and wiring to the new pump. This will also be triggered from the ecu, but i might just take new connections to appropriate wires, such as ignition live and battery etc.

    Does that sound plausible?
    Likes James5 liked this post

  17. #17
    Committee, Treasurer, Memberships admin Ian S's Avatar
    Join Date
    Sep 2000
    Location
    Essex
    Posts
    5,832
    Post Thanks / Like

    Re: fuel relay wiring

    Do you want the safety of the pumps being stoped if the engine stops?

    If so, then have the original fuel pump electrical module operate them both.

  18. #18
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Quote Originally Posted by Ian S View Post
    Do you want the safety of the pumps being stoped if the engine stops?

    If so, then have the original fuel pump electrical module operate them both.
    Thanks Ian. The Adaptronic takes care of that as it only triggers the pump on prime and then when the engine is turning, sensed via the tdc sensor.
    Likes James5 liked this post

  19. #19
    Committee, Treasurer, Memberships admin Ian S's Avatar
    Join Date
    Sep 2000
    Location
    Essex
    Posts
    5,832
    Post Thanks / Like

    Re: fuel relay wiring

    Have the Adaptronic power them both?

  20. #20
    Committee, Moderator Matt Cole's Avatar
    Join Date
    Sep 2008
    Location
    Durham
    Posts
    5,259
    Post Thanks / Like

    Re: fuel relay wiring

    Ok. Update and all sorted!😁 I rewired both relays the same and used the ecu to trigger both. Everything up and running. Nearly finished the fuel system so will update once done.
    Likes Ian S, James5 liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •