Anyone know the thread size for the oil feed on the 200sx t28? Looks like an m10 with a 1mm thread pitch but I want to be sure as I have nothing to measure the thread with.
Anyone know the thread size for the oil feed on the 200sx t28? Looks like an m10 with a 1mm thread pitch but I want to be sure as I have nothing to measure the thread with.
Gary take the turbo and your turbo oil feed pipe to your local Pirtek matey and they will find you an adaptorOriginally Posted by SCHWARTZ
Anyone know the thread size for the oil feed on the 200sx t28? Looks like an m10 with a 1mm thread pitch but I want to be sure as I have nothing to measure the thread with.will only cost you a few £'s
There's one in Mitcham matey
Pirtek, Unit 11 Liongate Enterprise Park, 80 Morden Road, Mitcham, Surrey, CR4 4NY
Tel: (020) 8640 6565
nice one matey il pop down there
Make sure you find out though as I need one as well
will do
4an? is that a thread hose solutions are likely to use? Il call them but il most prob go down to pirtek with the turbo and old adaptor so i know it will fit.
worst case if they don't tell you the invoice should have the pirtek part number onwill do
If it helps steve il pick you one up just need to know how you want the other end.
Thats would be a great help mate, not sure, I'll prob get Ben @ Hose soloutions to make it so I can specify
he did mine so il get 2 of the same
Went to pirtec turns out its next door to where I get the car mot'dbut they had nothing that would fit the turbo
they had parts to fit the hose but not the turbo.
The search continue's...
I may ask CR Turbo's tomorrow if they know the size & then at least we can go from there with adapters ??
good shout matey. il find out the size of the oil feed hose thread from ben.
Guys it's a very funny size as I have tried loads of different adapters, the link I put up is the only one I could get to fit.
Im finding that out bud
I've just bought a fitting M14 - 4an, that way I can tell if it fits the oil pressure switch outlet & the turbo
Good man let me know how you get on
Still need to know what fittings Ben can use or does use on the feeds though.....Good man let me know how you get on
Also found this place http://www.speedflowshop.co.uk/male-...lers-103-c.asp
Ace one of those must do it. Im going to ring ben on monday as hes the only one who will know what the thread size is on the feed aparently
Which end goes into your turbo though, the 1/4 or the 4an ?
Says 1/4 inverted flare so would have thought that end in the turbo. Could be wrong though.
Woop woop
So we want 1/4 not 4an to go into the turbo ...
Yep, caus I then joined the 4an to a double ended female 4an that attached to my male 4an filter!So we want 1/4 not 4an to go into the turbo ...
Quite poss my oil feed is 4an female remember that being mentioned but not sure.
Good chance as the female connectors look the same on my gt turbo hose solutions turbo oil feed, not measured though. Think 4an is a fairly standard size for turbo oil feeds.
Yep, caus I then joined the 4an to a double ended female 4an that attached to my male 4an filter!
Im sure 4an was mentioned somewhere il wail til mon n see if ben can confirm that
Well I got an adapter M10x1mm & it's to small & the 1/4" I got was way too big (unless the ysent the wrong adapter).
The actual size according to CR Turbo's is: 7/16 UNS 24 tpi, they sell adapters for £17.50 + VAT & carraige...
fookin ell how much!!!i should be making these at work if i had the time.
Well I got an adapter M10x1mm & it's to small & the 1/4" I got was way too big (unless the ysent the wrong adapter).
The actual size according to CR Turbo's is: 7/16 UNS 24 tpi, they sell adapters for £17.50 + VAT & carraige...
What exacly is it you need? i have a guy near me who made all my barided hose for my engine he has adaptors etc coming out his ears.
I need the above size for my turbo so i can make an oil feed up, the adapter to 4an (or is it 6an) is hard to find...
Steve ben from hose solutions has them just tell him you want an adaptor when you get your oil feed hose made up. He sent me one out for free so it didnt feel right to ask for another one. I was hoping that he would tell me the size when he sent it but he kept that quietIl give him a ring if ya want and see what he sent me if you like?
Steve ben from hose solutions has them just tell him you want an adaptor when you get your oil feed hose made up. He sent me one out for free so it didnt feel right to ask for another one. I was hoping that he would tell me the size when he sent it but he kept that quiet
Nope, they are some of the ones I bought, none the right size
Is 8mm id hose enough for an oil return hose or does it need a larger dia bore ?
Have a look at this Steve, 8mm would be way to
Small. Think it should be somewhere around 14mm.
https://www.rtoc.org/boards/showthread.php?t=16387
the return on the b18ft is 16mm
Posting Permissions
Reply With Quote