Printable View
as above 200mm 4 paddle sprung centre plate for 5 gt and early clio.been ringing around a few places and got down to the nitty gritty the cheapest i can find is 147.12 all inclusive but the guy says if we wanna buy 10 then a 15% discount will apply..any takers please post on ere or pm me cheers.:)
I'm in.
1) Jaffa
2) 5teve L
3)
4)
5)
6)
7)
8)
9)
10)
..Quote:
Originally Posted by D4WNO
Any discount for 5 Jaffa ?
In case we struggle for the 10 :D
if i get 5 i can always ask m8 :)
:agree:
is this off Antony at techcraft lad? :cool:
English is not my motherlanguage, so I have to ask:
could you explain; is the center plate just the plate without friction surfaces or are you talking about "full" clutch plate?
Just the centre plate Harri, 4 paddle, no outside cover or release bearing.
HTH
Steve
The plate on the right of this picture
HERE
Ok, thanks. I've been thinking (more like worrying) that i have to buy the paddle clutch kit at some point.
Quote:
Originally Posted by WADDIE
no m8 direct from helix.:)
thats a good price lads, get them while they're cheap. and if you don't know, you'll want to use them in a volvo cover ;)
1) Jaffa
2) 5teve L
3)Alastair - if we get 10.:agree:
4) Bigfoot - if we get 10 as well :)
5)
6)
7)
8)
9)
10)
I may have to buy one of these direct as I need one ASAP.. PM Jaffa.
I'll take one if you get any form of discount, even only 5%. :agree:
pm m8 :)Quote:
Originally Posted by Alastair
do they do 1 in 215 mm?
Jaffa, PM'd. Need your paypal as HSBC 'error 998' keeps coming up, if you haven't already ordered. If you have then i can wait and order one later.Quote:
Originally Posted by jaffa
At what point is this clutch plate required; approximately when does the Valeo (green box) setup start to slip?
If I were running a full T25 and Piper285 cam type setup at 1.6bar would I be borderline ok with the normal Valeo clutch?
How does this plate hold up in normal road use (wear and ease of use)?
The volvo is prob ok for 1.5 bar manifold for quite a while if you don't use drag tyres Dave, mine lasted a few thousand miles with 1.5 bar (& a few times at 1.7) on a low comp engine & a few pod days/normal road use, didn't slip when I took it out, I only went to an AP plate as I was upping the boost & using drag tyres at pod (20 plus runs with no slip).
I found the AP ok for road use (albeit about 2k miles) although the wife said she hated it compared to her standard clutch.
Depends on what you plan on doing with the car & what sort of power you hope to get out of it, if you think you will be going up to & over 220lbft I'd just go with a paddle plate & volvo cover from the off TBH.
Is the man called Jaffa away on his jollies ??
Quote:
Originally Posted by 5teve L
yes m8 but still got time for u xxxxx
:laugh:
Couple of PM's for ya :cooter:Quote:
Originally Posted by jaffa
Cheers for sorting mine out so fast mate, spot on ;)
Quote:
Originally Posted by 5teve L
a pleasure m8 got another 2 on the way for others :)
Are these still available? And in 215mm?
I'm using the 215mm one. Ordered from techcraft about £180 +vat:agree:
would make them approx £125 all in if i'm correct?Quote:
Originally Posted by Bigfoot
this thread started a while ago so dont know if it went ahead or what or is still going on:scratch:
is that without pressure plate?Quote:
Originally Posted by MATT C Ringworm Tuning
Yes mate, it is a 6 plate paddle, friction plate only. I use the valeo pressure plate. No issues with 260 odd ft/lb of torque!Quote:
Originally Posted by SCHWARTZ
Part no. 77-5108 HD.
Dam good bit of kit too!!:agree:
This went ahead gary, think jaffa got these clutches in 200mm for me, steve and himself.Quote:
Originally Posted by SCHWARTZ
oh ok looks like i will have to pay the £180 and maybe get a new pressure plate then.
is it better to use a stronger pressure plate with these friction plates? or will it not make much difference? I cant see my lump making any more than 230bhp so dosnt need to be amazing. Would at least getting a new standard pressure plate help or do they not wear out really?
I was just told to use the standard pressure plate used in the valeo green box kit.
Il have a look for one cheers matey;)
I know this thread is old but was wondering if these are the best plates to use as i think my clutch is beginning to slip .... any surefire way to check ???
Who or where is the best place at the moment to buy them from ???
Thanks.