plumbing up the carb

[c5 swh]

Spent today fitting all the pipes to the engine bay, All coolant hoses, breather hoses. fmic etc. now im stuck :dearme:

I need help with where and how i attach the accelerater cable, choke cable, spring etc the pictures here will show how ive guessed it but i dont think its right,

http://img.photobucket.com/albums/v721/shanehandley/SL702493.jpg
http://img.photobucket.com/albums/v721/shanehandley/SL702494.jpg

How do the cables get held in place?

Also does the fuel lines look like there going into the right postion on carb does the one ive not attached go on the bit at top of carb??

Also ive got all this left over, vacum hoses i think does anyone have any pictures of where it all goes:cry:
http://img.photobucket.com/albums/v721/shanehandley/SL702495.jpg

thanks

[Hoolio]

May help, have to say i think you've done a great job on the engine.

[James5]

Your setup needs a couple of changes to be correct.

The 1st, 2nd and 3rd pics you can see how the carb linkage attaches, Yours is upside down (Excuse the state of the engine bay it is of my last 5)

The 4 pic I have shown you on your pic where the a/c cable secures to

[Andrew Cooke]

You've got some pretty entertaining plumbing yourself there James

[royz]

the choke cable has a metal cilp that holds it on to the bracket it is next to. as for the fuel line it needs to go above the one its on now.

[markey b]

the choke cable has a metal cilp that holds it on to the bracket it is next to. as for the fuel line it needs to go above the one its on now.

but a cable tie will do the job just the same

[James5]

You've got some pretty entertaining plumbing yourself there James


:laugh: The pics are of an old R5 when I used to do pretty much do as the tuners said:o.

Things have changed now thanks to RTOC showing me the way:smokin:

A couple more pics that may be of help from my last C1J

[James5]

but a cable tie will do the job just the same

Or a spare clip of the back of the heater controls (if you have a spare)

[Andrew Cooke]

if you use silicon vacuum hose always put a clamp or tyrap around it as it will expand and start to leak on boost.

[c5 swh]

thanks for the pics they should help. what about the picture below (sorry about my paint editing im in a rush got to go work):ashamed:
http://img.photobucket.com/albums/v721/shanehandley/SL702494-1.jpg

is the pipe ive circled orange in correct place?

Does the other pipe go where the orange arrow points to carb top.

And what goes to the bit circled red?

Also if i want to get rid of all the pipes and do the infamous 'cup mod' can you still run a dumpovalve?

Also where does the metal piping go to on this bit?
http://img.photobucket.com/albums/v721/shanehandley/SL702495.jpg

[markey b]

metal piping goes to turbo elbow, you've prob got a wheelbolt in there tho ;)

[James5]

is the pipe ive circled orange in correct place? No that should be on the bit your circled Red (Fuel Line in)

Does the other pipe go where the orange arrow points to carb top. YES

And what goes to the bit circled red? Fuel Line

Also if i want to get rid of all the pipes and do the infamous 'cup mod' can you still run a dumpovalve? Yes - you will need to T into the AEI vacum line

Also where does the metal piping go to on this bit? - Not sure never had a 5 with one on :laugh:

[c5 swh]

is the pipe ive circled orange in correct place? No that should be on the bit your circled Red (Fuel Line in)

Does the other pipe go where the orange arrow points to carb top. YES

And what goes to the bit circled red? Fuel Line

Also if i want to get rid of all the pipes and do the infamous 'cup mod' can you still run a dumpovalve? Yes - you will need to T into the AEI vacum line

Also where does the metal piping go to on this bit? - Not sure never had a 5 with one on :laugh:

Thats great will do it tomorrow:cool:

[scratcher]

The metal pipe screws into the turbo elbow :agree: But if you're 'cup modding' it you'll want to block it off with a bolt on the elbow.