PDA

View Full Version : driveshaft pin


J$£5GTT
05-04-2009, 19:07
i have tried to drift this out,its moved about 10mm but its not shifting
know more ??
:confused:
RICHIE
05-04-2009, 19:12
i have tried to drift this out,its moved about 10mm but its not shifting
know more ??
:confused:

roll pins are high tensil so will be hard to drill out have you used a hole punch
Chris Hebden
05-04-2009, 19:14
Have you tried moving the drive shafts about to try and realign them again?
gtmatt
05-04-2009, 19:23
loads of wd40 , then a roll pin punch is needed , i used a snap on one , im sure u will be able to get one from some where:)
J$£5GTT
05-04-2009, 21:32
cheers,soaked in wd40 for tanite,going to get myself a decent parallel
punch.
:agree:
sonic-jdm
05-04-2009, 21:32
Does anybody know where i can find a driveshaft pin from??? as ive lost mine:ashamed:
markey b
05-04-2009, 21:33
renault... 35p :agree:
J$£5GTT
05-04-2009, 21:45
renault... 35p :agree:

:agree::D
sonic-jdm
06-04-2009, 08:47
renault... 35p :agree:


bargin:eek::)
Sparkie
06-04-2009, 11:03
split pin....easier to remove.
TrixNFlix
06-04-2009, 11:11
Sorry to crash this thread but should I be worried that I don't have the pin in my driveshaft?:(
sonic-jdm
06-04-2009, 11:53
Sorry to crash this thread but should I be worried that I don't have the pin in my driveshaft?:(


Its not a good idea to drive with out the pin in, if you do full lock and look down at the drive shaft you can see its slipped half on and half off, so i guess with abit of hard driving and the shaft slipping on and off, i wouldnt take long till it chews the spines up!!

I wouldnt like the shaft to pop off at 70mph:eek: the first thing its going to hit when it swings round is the back off your bloke!;)
Sparkie
06-04-2009, 12:35
if you are really worried, push a nail into the hole and bend the ends over.
Chris Hebden
06-04-2009, 12:59
Am i right in thinking that the pin it self isnt under any stress?
Sparkie
06-04-2009, 17:23
there are two rubber CV boots holding that whole shaft together.... its not under that much stress.
J$£5GTT
06-04-2009, 19:45
purchased a quality parallel punch today,only few quid,anyways that
pin is now smashed right out.
:agree::cool:
Mr Raider
07-04-2009, 13:37
Had bit of ,mare with mine, lined the shafts up however on oneside the hole is perfectly aligned, the other around half a spline out. Put the roll pin in with hammer, now cant get the fecker out!:crap: Have to invest in a decent punch too to get it out as it bit chewed now. So take it they aint lined up quite right then?
Sparkie
07-04-2009, 15:48
yours is 180deg out...
TrixNFlix
07-04-2009, 18:40
Had bit of ,mare with mine, lined the shafts up however on oneside the hole is perfectly aligned, the other around half a spline out. Put the roll pin in with hammer, now cant get the fecker out!:crap: Have to invest in a decent punch too to get it out as it bit chewed now. So take it they aint lined up quite right then?



yours is 180deg out...



Feck, another two jobs on the ever rising list of jobs :sad2: