Josie172cup
22-04-2013, 08:07
Hi, a quick list of parts i think i still need. The list is just an edit of James5's list.
Unfortunately i can't buy all the parts at once so its going to be as and when.
Head Bolts
Phase 1 16v ECU with chip carrier
Phase 1 16v engine loom with relays and brown and white plugs on for F7p conversion
Phase 1 16v Low or High Boost fast chips chip for F7p conversion for Phase 1 ECU
Valver Gearbox
Turbo downpipe (i have a R5 one)
One way valve for brake system
One way valve for crankcase breather to inlet 8mm id
Fuel pump external either Bosch 044 or Walbro 255 type
Fuel lines from GTT sender to your external pump
Fuel line 1 meter 10mm id
Fuel lines 8mm id about 2.5 m
Turbo T25 or T28 dependent on boost chip running low or high
Oil feed and oil drain adapters
Drill and tap block for oil drain
K-Tec or BBPT Clio 1 down pipe
GTX front engine metal mount or drill R5GTT metal mount
GTX or Volvo alternator lower bracket and upper bracket
Alternator F7P
Starter motor F7P
Clio 16v Coil pack
Heat shield material for bulkhead to protect brake servo / cylinder
Clio 16v throttle cable
Throttle body gasket - 7700740706
TDC sensor
Alternator belt
Stuff i might not need, i would like the turbo looking at though. Also may need a new clutch and fly cant remember if i have a fly or if its any good. i do however have a few r5 clutches lying around not sure if they're of any use?
I could probably do with buying the ECU and looms first. Oh and head bolts.
If there is anything else you may have that could be of any use let me know ill probably buy it. There is probably loads more i'm missing haha
Thanks for looking, I'll edit this thread as i go.
Joe
Edit:
Parts Acquired / no longer needed
Parts I need ASAP
Unfortunately i can't buy all the parts at once so its going to be as and when.
Head Bolts
Phase 1 16v ECU with chip carrier
Phase 1 16v engine loom with relays and brown and white plugs on for F7p conversion
Phase 1 16v Low or High Boost fast chips chip for F7p conversion for Phase 1 ECU
Valver Gearbox
Turbo downpipe (i have a R5 one)
One way valve for brake system
One way valve for crankcase breather to inlet 8mm id
Fuel pump external either Bosch 044 or Walbro 255 type
Fuel lines from GTT sender to your external pump
Fuel line 1 meter 10mm id
Fuel lines 8mm id about 2.5 m
Turbo T25 or T28 dependent on boost chip running low or high
Oil feed and oil drain adapters
Drill and tap block for oil drain
K-Tec or BBPT Clio 1 down pipe
GTX front engine metal mount or drill R5GTT metal mount
GTX or Volvo alternator lower bracket and upper bracket
Alternator F7P
Starter motor F7P
Clio 16v Coil pack
Heat shield material for bulkhead to protect brake servo / cylinder
Clio 16v throttle cable
Throttle body gasket - 7700740706
TDC sensor
Alternator belt
Stuff i might not need, i would like the turbo looking at though. Also may need a new clutch and fly cant remember if i have a fly or if its any good. i do however have a few r5 clutches lying around not sure if they're of any use?
I could probably do with buying the ECU and looms first. Oh and head bolts.
If there is anything else you may have that could be of any use let me know ill probably buy it. There is probably loads more i'm missing haha
Thanks for looking, I'll edit this thread as i go.
Joe
Edit:
Parts Acquired / no longer needed
Parts I need ASAP