PDA

View Full Version : My 5GTT efi.


la turbine 63
31-07-2012, 23:10
First post!

Hello, i present my project 5GTT ph2, year 1985 white 389.

Engine

- piston Wössner
- FGS800 shirt
- 314 cat cams camshafts
- Dump Bonalume
- Inoxline exhaust manifold
- Intake manifold injected R5GTT
- Megasquirt ECU, sequential injection, ignition coil jumostatique, Map 0/43 psi, launch control and flat shift
- Walbro fuel pump
- rev limiter 7200
- ratio of 8.0 / 1
- down pipe KTR 2 "1/2 (63mm)
- exhaust system KTR 2"1/2 (63mm)
- T25/T28 Hybrid turbo
- Intercoller forge
- 13 oil ranges
- S5 radiator diesel

Turbo type

-T25/T28

Boost Pressure (@ manifold)

-20psi

Transmission

- JB3032

Wheels

- 15" Compomotive Gr.A

Suspension Details

Front:
- Viarouge
- Apex -45mm
- 20mm spacers

Rear:
- Viarouge
- Clio 16V rear-wheel axle unit

Brakes

- Pug 406 V6 23,8mm master cilinder
- Brake caliper Brembo, front disc 280 clio rs.

Interior

- Sparco seats
- Multipoint cage hoops

photograph here :

http://img4.hostingpics.net/pics/722361dscn1433bisuz5.jpg

http://img4.hostingpics.net/pics/468037dscn1465bisck3.jpg

http://img4.hostingpics.net/pics/864649photo217gc6.jpg

Multipoint cage hoops :

http://img4.hostingpics.net/pics/612275dscn1528bisal0.jpg

front :

http://img4.hostingpics.net/pics/218967pfhoto004em9.jpg

Inside :

http://img4.hostingpics.net/pics/203652photo120jf4.jpg

Engine :

http://img4.hostingpics.net/pics/423322104zs006.jpg

connecting rods and pistons Wossner :

http://img4.hostingpics.net/pics/707619montagechemisepistonbielle009.jpg

CAMSHAFTS Cat cams 314, SPRINGS, PULLEYS KITS

http://img4.hostingpics.net/pics/879979photo002op3.jpg

Inlet manifold efi :

http://img4.hostingpics.net/pics/479107photo232tt1.jpg

T25/T28 :

http://img4.hostingpics.net/pics/868118t25t39.jpg

Engine :

http://img11.hostingpics.net/pics/153863gtjef015.jpg

The cars :

http://img11.hostingpics.net/pics/223547GtJeff034b.jpg

http://img11.hostingpics.net/pics/115334GtJeff030b.jpg

http://img11.hostingpics.net/pics/511076GtJeff024.jpg

;)
rs250nut
31-07-2012, 23:21
Nice car and welcome to the club:) Did the cage get installed in one piece?
la turbine 63
31-07-2012, 23:39
New poster! (less than 10 posts)

Thank you.

This is a cage hoops sections to several parties, realized by me.

http://img84.imageshack.us/img84/1737/photo359gm9.jpg
allanr5gtt
31-07-2012, 23:48
welcome good to see another efi r5. great pic's as well
Mudslinger
01-08-2012, 00:02
Very Nice :agree:
TNT ANDY
01-08-2012, 06:17
Oooh la la - impressionnant!
dangerous dave
01-08-2012, 10:11
Lovely... :agree:
Tutuur
01-08-2012, 10:19
wow awesome project! needs more detailed pics:)

very curious on the holes made for the cage...
Kris M
01-08-2012, 12:35
Excellent
la turbine 63
02-08-2012, 17:50
New poster! (less than 10 posts)


wow awesome project! needs more detailed pics:)

very curious on the holes made for the cage...


The base:

http://img11.hostingpics.net/pics/438047DSCN1432.jpg

the tubes :

http://img11.hostingpics.net/pics/247660DSCN1431.jpg

reinforcement :

http://img11.hostingpics.net/pics/268018DSCN1493.jpg

http://img11.hostingpics.net/pics/629220DSCN1504.jpg

http://img11.hostingpics.net/pics/630443DSCN1508.jpg

http://img11.hostingpics.net/pics/807782DSCN1516.jpg

http://img11.hostingpics.net/pics/431974DSCN1538.jpg

http://img11.hostingpics.net/pics/761780DSCN1540.jpg

http://img176.imageshack.us/img176/8344/photo357zr3.jpg

http://img11.hostingpics.net/pics/565870IMG2418.jpg

http://img11.hostingpics.net/pics/252379IMG2417.jpg
Alastair
02-08-2012, 20:45
Great project mate, but where are your harness bars on the cage? Have i missed them or are you going a different route?
Hi 5
02-08-2012, 21:01
very nice like the cage
chipis
02-08-2012, 21:44
how much power are you running with 20psi?
Tony Walker
02-08-2012, 22:20
Amazing work, love the effort put in to the shell before anything else :agree:
la turbine 63
02-08-2012, 23:32
New poster! (less than 10 posts)


Great project mate, but where are your harness bars on the cage? Have i missed them or are you going a different route?

http://img11.hostingpics.net/pics/732025gtJeff276.jpg


how much power are you running with 20psi?

http://img15.hostingpics.net/pics/806135grgtJeffpassageobanc001.jpg

http://img15.hostingpics.net/pics/630176grgtJeffpassageobanc003.jpg

Result 220cv and 30 m.kg torque.
Alex
03-08-2012, 07:59
Proper job! :agree:
Woznaldo
07-08-2012, 13:31
My kind of 5. Love it! :cool:
REBEL GT TURBO
31-08-2012, 23:40
Very cool car!
la turbine 63
28-12-2012, 22:21
New poster! (less than 10 posts)

Here are the latest developments alpine turbo with aac alpine R5 turbo:

The water pump modified :

http://img15.hostingpics.net/pics/913042montagealpine1.jpg

http://img15.hostingpics.net/pics/186065montagealpine18.jpg

Valve :

http://img15.hostingpics.net/pics/769882montagealpine35.jpg

http://img15.hostingpics.net/pics/601806montagealpine37.jpg

Screw in 12.5 :

http://img15.hostingpics.net/pics/630966montagealpine43.jpg

Cup sinks candles, push rod and aac type "mini GR.A" and "GR.A" R5
turbo :

http://img15.hostingpics.net/pics/423052montagealpine25.jpg

Door pulley crank out more 25mm :

http://img15.hostingpics.net/pics/820358montagealpine53.jpg

alternator support :

http://img15.hostingpics.net/pics/755758montagealpine57.jpg

My 4 in 1 Stainless :

http://img15.hostingpics.net/pics/381359Divv096.jpg

http://img15.hostingpics.net/pics/386671montagealpine76.jpg

for a descent oil :

http://img15.hostingpics.net/pics/244258montagealpine84.jpg

Assemble the engine :

http://img15.hostingpics.net/pics/416824montagealpine125.jpg

http://img15.hostingpics.net/pics/260571montagealpine127.jpg

In the engine compartment :

http://img15.hostingpics.net/pics/120370montagealpine180.jpg

http://img15.hostingpics.net/pics/354822montagealpine206.jpg

Two small video :

engine (http://youtu.be/fERUAUHuHEg)

Exhaust (http://youtu.be/c_Z9VcIHAuw)

;)
bood
28-12-2012, 22:28
excellent work, very interesting :agree:
Jonny5
28-12-2012, 23:04
Great work :agree:
Love the look of the alpine head in a 5gtt engine bay.
Tutuur
28-12-2012, 23:11
looks really good! this is the stuff we want to see!!!!

will this one be at the Meeting desn Sangliers 2013?

would love to see it in real life!
Woznaldo
01-01-2013, 01:22
Love these kind of builds! Great work, have you had it set up on a Dyno yet?
HAndy
01-01-2013, 10:30
really nice build there, well done:cool::cool::cool:

the best 1.4 pushrod engine set up:smokin:
Matt Cole
01-01-2013, 10:31
Very nice! Nice thought out and engineered conversion and restoration. Would love to see this in the flesh. :agree:
la turbine 63
01-01-2013, 13:05
New poster! (less than 10 posts)

Thank you.


looks really good! this is the stuff we want to see!!!!
will this one be at the Meeting desn Sangliers 2013?
would love to see it in real life!

Yes, it may be possible.


Love these kind of builds! Great work, have you had it set up on a Dyno yet?

no, not yet.


really nice build there, well done
the best 1.4 pushrod engine set up

My engine configuration :

- piston Wössner
- FGS800 shirt
- Cylinder head R5 alpine turbo
- ratio of 8.0 / 1
- PUSH ROD r5 turbo 2
- Camshafts R5 turbo 2 TDC
- 4 en 1 exhaust manifold home
- down pipe KTR 2 "1/2 (63mm)
- exhaust system KTR 2"1/2 (63mm)
- T25/T28 Hybrid turbo
- Intake manifold injected R5 turbo
- Megasquirt ECU, sequential injection, ignition coil jumostatique, Map 0/43 psi, launch control and flat shift

Currently under adjustment. ;)
danielmk323
01-01-2013, 13:35
New poster! (less than 10 posts)

Thank you.



Yes, it may be possible.



no, not yet.



My engine configuration :

- piston Wössner
- FGS800 shirt
- Cylinder head R5 alpine turbo
- ratio of 8.0 / 1
- PUSH ROD r5 turbo 2
- Camshafts R5 turbo 2 TDC
- 4 en 1 exhaust manifold home
- down pipe KTR 2 "1/2 (63mm)
- exhaust system KTR 2"1/2 (63mm)
- T25/T28 Hybrid turbo
- Intake manifold injected R5 turbo
- Megasquirt ECU, sequential injection, ignition coil jumostatique, Map 0/43 psi, launch control and flat shift

Currently under adjustment. ;)
very nice build man can i ask what liners you use on the build
Tony Walker
01-01-2013, 13:56
Very exciting.....:agree:
Tutuur
01-01-2013, 18:45
i think those fgs800's are the liners
la turbine 63
01-01-2013, 20:21
New poster! (less than 10 posts)

Me cylinder Liner fgs800
danielmk323
02-01-2013, 07:33
New poster! (less than 10 posts)

Me cylinder Liner fgs800
ok tanks do you have a link for them or are custom build
la turbine 63
06-01-2013, 20:11
New poster! (less than 10 posts)

custom build !


New video :

http://youtu.be/fjWYcf0Ke7M

:)
gardner51
17-01-2013, 18:45
Very nice indeed!

are you using stock elbow to downpipe?

could free up some breathing by getting a one piece?

Elliott
Ashy
17-01-2013, 19:45
Looks awesome mate, great conversion!
Fred²
18-01-2013, 15:42
New poster! (less than 10 posts)


ok tanks do you have a link for them or are custom build

You can purchase the liners here :
http://www.gtturbo-online.fr/bas-moteur/393-4-chemises-fonte-gs-800.html

If you want to call, the store's owner do speak english.
danielmk323
18-01-2013, 16:59
New poster! (less than 10 posts)



You can purchase the liners here :
http://www.gtturbo-online.fr/bas-moteur/393-4-chemises-fonte-gs-800.html

If you want to call, the store's owner do speak english.
Tanks for the link