door hinge repair kits

[Schakal]

prices would be

£8 for 4 brass bushes ( no torx pins /covers 1 door )
£12 for 4 brass bushes and 2 torx pins ( covers 1 door )
both prices include delivery via standard 1st class post


these should be ready to post next wednesday (17th feb 2010).

they will be sold on a first come first served basis .

payments can be sent to schakalx@hotmail.com
as a "GIFT" and pm me your delivery address on here as it wont
come up on paypal as well as how many bushes and/or pins
you want .


as my doors are out at the moment , i have been looking into
getting some new pins and bushes in there to fix the "droppy door"
syndrome . finally located some pin and brass bush kits .

as far as i understand these brass bushes are whats fitted to the
doors from the factory to take the wear so that the hinges dont take
the damage , once the bushes and pins wear out you get
droppy doors .

here is a picture of the kit to cover 1 door .

http://www.rtoc.org/boards/picture.php?albumid=498&pictureid=10280

[Penfold aka The Dealer]

Could be tempted depending on price.. :)

[Matt Cole]

My bro needs these, price good sir?

[Schakal]

prices would be

£8 for 4 brass bushes ( no torx pins /covers 1 door )
£12 for 4 brass bushes and 2 torx pins ( covers 1 door )


both prices include delivery via standard 1st class post .

[djinuk]

do these torx type fit all r5s? ,

Also do you have a rough guide on how hard they are to fit.

thanks dj

[philg]

i might need 1 set to

phil

[phase i 16 v turbo]

do these torx type fit all r5s? ,

Also do you have a rough guide on how hard they are to fit.

thanks dj


No but you can make them fit. I have had these kits for sometime. They work well.

[JamesF]

I'd like a set too. Cheers

[Brigsy]

Ill have a set of bushes/2no torx pins:)

[Penfold aka The Dealer]

For that price i would have 2 set's.

[Schakal]

i will order about 100 brass bushes and 30 torx pins for starters .
these should be ready to post next wednesday (17th feb 2010).

they will be sold on a first come first served basis .

payments can be sent to schakalx@hotmail.com
please dont forget to type how many bushes and/torx pins
you want in the paypal message .

[Schakal]

do these torx type fit all r5s? ,

Also do you have a rough guide on how hard they are to fit.

thanks dj



i will be replacing these on my car very shortly (for the first time :scared: )
will take some pictures and try to cover pros and cons as i go along
and if i feel confident enough ,i might make a guide out of it :)

[Scottish9Turbo]

i take it that renault dont do hinge pins anymore for 5's hence this?

[Ian S]

Am I correct in thinking that these only fit the later 5GTT hinges?

And that would also apply to the 9 and 11?

[Slim]

I would be interested. But i dont know which ones i need. Can anyone help?? or have any pics to show me the differences between the two (prefererably with the doors on the car)

my door is so bad it cant shut unless i line it up and push hard :ashamed: very embarrasing in car parks :(

[Adey aka Ewok]

let me know how you get on on the 9 bud as i do need to do both my doors

[Schakal]

I would be interested. But i dont know which ones i need. Can anyone help?? or have any pics to show me the differences between the two (prefererably with the doors on the car)

my door is so bad it cant shut unless i line it up and push hard :ashamed: very embarrasing in car parks :(



if you got torx pins looking from the top of the hinge you got
the setup in the top picture .
the other type is a split pin similar to these.

http://www.rtoc.org/boards/picture.php?albumid=498&pictureid=10335

[Schakal]

let me know how you get on on the 9 bud as i do need to do both my doors


i will be cracking on this week ,will let you know :agree:

[Schakal]

first lot of pins and bushes have been posted today to
whoever have bought from me :agree::agree:

[Schakal]

also had a quick go removing the old bushes on my car today .

best way to get the old ones seem to be a round/flat ended chisel
(2-3mm diameter ) and a hammer . to get the bottom bush i stick the
chisel from the top and find its edge to gently tap it out with the hammer.
opposite for the top bush obviously .

will have a decent go tomorrow as i will have more time .
try to take better pics to describe it .
here is old vs new , they are worn to fokkk , you put a new pin
in one of the old ones and the slack in it becomes obvious

http://www.rtoc.org/boards/picture.php?albumid=498&pictureid=10336

[Schakal]

guide for removal of the old bushes with pics .

http://www.rtoc.org/boards/showthread.php?t=13397


also last 4 torx pins to go !!! still got plenty of bushes left :agree:

[Slim]

hi mate... i want the kit for 2 doors... can u tell me exactly wat to do and how to do it... i have a paypal account but dont have a clue how to use it :scratch: :sad:

[Schakal]

hi mate... i want the kit for 2 doors... can u tell me exactly wat to do and how to do it... i have a paypal account but dont have a clue how to use it :scratch: :sad:


pm ed :agree:
if you get stuck ,pm me back and i will try to guide you through .

[Schakal]

offically ran out of full door kits including torx pins now .
brass bushes are still available :agree:

if there is any more interest in full kits please post on here
and i will get more in stock .

[Schakal]

Am I correct in thinking that these only fit the later 5GTT hinges?

And that would also apply to the 9 and 11?


thats right earlier hinges use this type pins i believe and there
are no bushes to take the wear .

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=140312856718&viewitem=&sspagename=STRK%3AMEWAX%3AIT

[Slim]

cant we make the bushes fit the old type at all??

[Schakal]

cant we make the bushes fit the old type at all??


good question . anyone on here have the old type door hinges
that can get me some measurements ?

[Ian S]

IIRC, no you can't, simply because the newer door hinges are much wider so that can take the bushes.

The old ones are too thin to have enough spare metal left once drilled out.

Someone did make some sleves for the old ones. 8mm OD, 7mm ID. 'Just' drill out the old hinge to 8mm, drift in the sleeve, fit a new OE roll pin.

But don't pay US$80 for the 4 pins though!! :sad2:

[Schakal]

IIRC, no you can't, simply because the newer door hinges are much wider so that can take the bushes.

The old ones are too thin to have enough spare metal left once drilled out.

Someone did make some sleves for the old ones. 8mm OD, 7mm ID. 'Just' drill out the old hinge to 8mm, drift in the sleeve, fit a new OE roll pin.

But don't pay US$80 for the 4 pins though!! :sad2:

thats true . i think the thickness of the bushes for the new type is the
same as the thickness of the older style pins .

however the hinges on the doors can be changed to new style ones ,
the hinges on the car chassis will take the bushes and it should
work in theory .

[Schakal]

Can you explain more what you mean about "cut the hinges from the middle".

Thanks.

Do you mind if I add this to the existing article on door hinges?

i cant reply to my "droppy door fix thread" :crap:
what i mean is the hinges coming out from the chassis as per below picture .

http://www.rtoc.org/boards/picture.php?albumid=962&pictureid=10436

using one of these on an angle grinder/die grinder etc .
(you get better access for cutting front door ones ,once the wings are out )

http://www.yan-mo.com/en/userdata/image/501/20080123115648105_Resinoid_Cutting_Disc.jpg


and once the door is off its easier to remove rounded/rusted pins .
than you can weld the bits you chopped back ,grind the welds down
to flat etc etc .

[Ian S]

i cant reply to my "droppy door fix thread"

That's because it's now in the articles section. Miller moved it there. :) Only now you're prevented from adding to it.

Anything from this thread can be moved over though.

[Slim]

ok.. I have the new pins and bushes..... but they look much larger than anything i have on my door.... does this mean i have the old type right? :(

Is there anything i can do about my door? its so bad it wont shut anymore! :( does it mean i need a new door or I have to source the pins for it??? i really dont know much about this door stuff!:scratch:

[Slim]

Is ht hinge on the actual body the same on all R5's? does anyone know this?

[Schakal]

Is ht hinge on the actual body the same on all R5's? does anyone know this?


i would say 95% same with only having seen the older type split
pin once . to convert the doors to new style you would need to
cut and weld from other doors (possibly from clio , r9 , r11 ,r19 ,r5 )
or get new door hinges and bolt/weld them on .

what year is your car ?? pictures would help also

[Brigsy]

ok.. I have the new pins and bushes..... but they look much larger than anything i have on my door.... does this mean i have the old type right? :(

Is there anything i can do about my door? its so bad it wont shut anymore! :( does it mean i need a new door or I have to source the pins for it??? i really dont know much about this door stuff!:scratch:

Sounds like you have the old style roll pins. Either drill the pins out & fit a bigger pin, or shim the worn hinge part on the car & fit new o.e sized pins, easy enough to do.

[Slim]

My car is a D reg... but its the same as my brothers which is an F plate :S

Brigsy... i would need new pins then... but the older pins are apparently much harder to get hold of and much more expensive ...

how about fitting just the pins (above) without the bushes??? will that fit :ashamed:

[Brigsy]

I doubt the bushes will fit with the old pins mate, easy enough to try when in bits though.

I cant see the old style knock in roll pins being expensive, i bought some from renault a few yr back & they were pennies! There only bog std 7mm roll pins iirc, not exactly special order stuff like the later torx fittings.

Search the boards, there was a topic on shimming the mounts that are attatched to the car, far easier than cutting/welding hinges off the door imo. Somebody even knocked up a batch of shims, i got a set here :)

[Slim]

I got no clue what you said in your last paragraph :scared:

but il go to renault and find out if they stock them and how much. I just thought they stopped stocking parts for the renault 5 Gtt thats alll :scratch:

thanks mate

[Slim]

In that case... does anyone want to buy the pins i just bought?? :confused: lol

[Schakal]

In that case... does anyone want to buy the pins i just bought?? :confused: lol


i might have a set of older style pins i can part ex with you
seeing that you bought those from me .
but in the long run its always best to convert your doors to
later style . the reason renault done this is because as well
as the pins , insides of the hinges were getting worn on older style imo .

[Slim]

i might have a set of older style pins i can part ex with you
seeing that you bought those from me .
but in the long run its always best to convert your doors to
later style . the reason renault done this is because as well
as the pins , insides of the hinges were getting worn on older style imo .

lol.. hmmm ok so what deal can you make? :scared: and do you know how much it would be from renault?

[Schakal]

lol.. hmmm ok so what deal can you make? :scared: and do you know how much it would be from renault?


pm ;)

[JamesF]

Changed the bushes and pins on my car the other day and it now shuts perfect. Thanks Schakal.

The only problem I had was getting the top bushes out, but once they're out you can just knock the bottom one down pretty easy, I used a screwdriver and it came straight out.

Cheers. :)

[Schakal]

Changed the bushes and pins on my car the other day and it now shuts perfect. Thanks Schakal.

The only problem I had was getting the top bushes out, but once they're out you can just knock the bottom one down pretty easy, I used a screwdriver and it came straight out.

Cheers. :)


nice one mate , i hope my doors will be fixed as well
once i fit them on after the respray :cool:

[Schakal]

all latest orders have been posted today guys .


also got the torx pins back in stock now .
give me a shout if you are after full door kits :agree:

[Scottish9Turbo]

are these copies of the hinge pins that renault still make mate?

[Schakal]

are these copies of the hinge pins that renault still make mate?


these are the originals mate :agree:
last time i checked with my local dealer it would be 2 weeks wait provided
they have them in stock .

[Schakal]

still got a few of these available :agree:

[prez06]

al have 4 bushes and the pins mate

[philg]

Torx get my thumbs up :agree:

Hate them pins :mad:

phil

[Schakal]

al have 4 bushes and the pins mate


will post them for you on tuesday mate :agree:

[Schakal]

got these back in stock guys :agree:
also available through my ebay shop

http://shop.ebay.co.uk/schakal16v/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686

[paul-11turbo]

Have you still got the bushes mate?

I will be wanting 8 to do both doors.

[Schakal]

yes mate , i have these in stock at all times now :agree:
pm me for payment details .

[Josie172cup]

any idea which ones i need m8

http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc6/183792_1783353340324_1134199525_2097179_6573648_n. jpg


EDIT: sorry didn't notice the date on this :(

[raj]

any idea which ones i need m8

http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc6/183792_1783353340324_1134199525_2097179_6573648_n. jpg


EDIT: sorry didn't notice the date on this :(

he still has them on ebay (http://cgi.ebay.co.uk/RENAULT-5-GTT-TURBO-9-11-19-CLIO-DOOR-HINGE-REPAIR-KIT-/280503485201?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item414f4f8311#ht_500wt_922)

[Josie172cup]

he still has them on ebay (http://cgi.ebay.co.uk/RENAULT-5-GTT-TURBO-9-11-19-CLIO-DOOR-HINGE-REPAIR-KIT-/280503485201?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item414f4f8311#ht_500wt_922)


are these deffinately the right ones? (newer style)

[Schakal]

are these deffinately the right ones? (newer style)

looking at your picture ,you seem to have the roll pin type (older style)

[philg]

looking at your picture ,you seem to have the roll pin type (older style)


:agree:

[Josie172cup]

looking at your picture ,you seem to have the roll pin type (older style)


nice one cheers Schakal, i didn't think it was the new shape.

is it worth my while trying to convert to the new type?