Viper 480 alarm [Archive]

Rob1980

18-09-2009, 13:38

I have got a new remote for the Viper 480 alarm as my keys got stolen and I was wondering if anyone knew how to reprograme it to the alarm??

I have called clifford and they will not help as I did not buy it from them even though I did purchase the original system off of them!! :jerkoff:

The company who I brought the replacement off have no idea either! :confused:

Can anyone please help?? It takes me 5 minutes to start my car at the moment as I manually have to override everything.

IANMM

18-09-2009, 14:25

http://www.rtoc.org/files/Miscellaneous/Viper%20480XV.pdf

start from page 18 and go from there

Rob1980

18-09-2009, 14:44

http://www.rtoc.org/files/Miscellaneous/Viper%20480XV.pdf

start from page 18 and go from there

Thanks a lot for that. Much appreciated. :agree:

IANMM

18-09-2009, 14:46

no probs :)

Rob1980

18-09-2009, 14:53

I have just read through it and it tells me how to programme the remote but not how to sinc it with the car so that it will respond or am I missing something??

I have not got the pager any more, just a new key fob...

Sorry to be a pain.

Rob1980

23-09-2009, 15:03

Can anyone help with my stupidness??

IANMM

23-09-2009, 16:31

got a piccy of the keyphob?

im sure you have to press the valet button 7 or 8 times to get it into the correct mode

IANMM

23-09-2009, 16:40

try this

Step 1: Open a door. (a car door... your car ;) )
Step 2: Put the key in the ignition and turn it to the "Run" position.
Step 3: Push & release the program button (the black button in your car - usually located under dash or driver's kick panel) once and then release.
Step 4: Push & hold the program button in (keep holding).
(Unit -should- chirp once)
Step 5: Press and release a button on your remote (this button will be your arm/disarm button)
Step 6: Release the program button.
Step 7: Press & Release the program button.
Step 8: Press & Hold the program button (do not release).
(unit should chirp twice)
Step 9: Press button2 (or the other button) on your remote.
Step 10: Release program button.
Step 11: Turn key off.
(Unit should emit a long chirp to confirm)

Let me know how it works.

IANMM

23-09-2009, 16:42

or its this one

they should all pretty much be the same to program.
open door, key on, press and release the valet switch 9x, then press and hold, the siren should beep 9 times. the press lock on both of your remotes. release the valet switch. key off. test
if it dosen't beep 9x,(does more) then turn the key off and back on and try again.

Rob1980

23-09-2009, 16:46

Thanks a lot mate. I will try these tomorrow and let you know how it goes.

Rob1980

01-05-2011, 15:18

try this

Step 1: Open a door. (a car door... your car ;) )
Step 2: Put the key in the ignition and turn it to the "Run" position.
Step 3: Push & release the program button (the black button in your car - usually located under dash or driver's kick panel) once and then release.
Step 4: Push & hold the program button in (keep holding).
(Unit -should- chirp once)
Step 5: Press and release a button on your remote (this button will be your arm/disarm button)
Step 6: Release the program button.
Step 7: Press & Release the program button.
Step 8: Press & Hold the program button (do not release).
(unit should chirp twice)
Step 9: Press button2 (or the other button) on your remote.
Step 10: Release program button.
Step 11: Turn key off.

(Unit should emit a long chirp to confirm)

Let me know how it works.

Sorry to bring this back from the dead but I tried this again today and it does not work.

I get to step 4 and it does not chirp, any ideas?? Its so frustrating!