Mark so where are the update pics:laugh:
Also which MSD coil did you go for??
Printable View
:cooter: pics need my laptop working to post them lol
got msd blaster coil in the end
http://i11.photobucket.com/albums/a1...k/DSC02759.jpg
here are couple of dash/wiring progress pics
http://i11.photobucket.com/albums/a1...k/ef69d9b5.jpg
http://i11.photobucket.com/albums/a1...k/7f47819b.jpg
http://i11.photobucket.com/albums/a1...k/08473467.jpg
pic as of last nite.... nearly done now
https://www.rtoc.org/boards/picture.p...ictureid=13950
getting there fella, is the column in the right place with the seat in?
looks great well done :)
As hard as you like!!! well done fella
New poster! (less than 10 posts)
stunning!! great workmanship mate.
finished! will post some pics once I've hoovered it out and cleared it out and put seats back in
a few pics from last nite, will get some better ones this afternoon when its back outside :)
wrong pics...
Love this car :goodJob:
flocked dash top arrived... just need to fit it, along with hundreds of more bits i've stockpiled :laugh:
https://www.rtoc.org/boards/picture.p...ictureid=14107
more bits to add to the ever increasing pile of 'parts to fit'
http://i11.photobucket.com/albums/a1...k/73ad3158.jpg
good news is i'll be moving into my new workshop start of feb so will be able to get much more done than my little unlit garage at the moment
latest update:
https://www.rtoc.org/boards/picture.p...ictureid=14981
after helping to oli's heater matrix sunday, got the car up the workshop and got started, finally got the AEM gauge in, MSD coil and toad up and running with remote lights and headlights, and dual zone proximity sensor.
still got a massive list, but will be working on it properly now i have the time/space :agree:
got oil cooler fitted now, something a bit different....
https://www.rtoc.org/boards/picture.p...ictureid=14999
https://www.rtoc.org/boards/picture.p...ictureid=14998
https://www.rtoc.org/boards/picture.p...ictureid=15002
https://www.rtoc.org/boards/picture.p...ictureid=15003
Thatll be nice when you hole it with a big stone :cooter:
Looks good, make sure you put some mesh behind it to protect from stones in the wheel arch, mine gets caked in crud and stones after a while! Have you got a stat' take off plate? I would recommend you fit one or you could run your oil too cool with the big rad!
i hardly use the car, but will mesh up behind it for some added protection. next on the shopping list is an oil temp gauge, and if its too low i'll add an inline stat :)
alot of hard work put in to it, least to say its all paid off stunning 5 mate !
few questions.. :)
whats with the MSD coil???
and where did you get your carbon splitter? looks the biz..
thanks :)
As said many times in the past about your 5... love it :agree:
msd coil is just higher output than the OE coil
http://i11.photobucket.com/albums/a1...k/138aa3ff.jpg
splitter is one I made, along with canards and fog ducts etc
out of interest mark, i see you hvae removed the front cross member for the intercooler, have to made a strut to go across the 2 and over the intercooler ? , just wondering as i removed my cross member but im contemplating making somthing to do the same job
this weekends progress was manifold and a few niggles sorted
http://i11.photobucket.com/albums/a1...k/ee4bca3f.jpg
http://i11.photobucket.com/albums/a1...k/55e43555.jpg
http://i11.photobucket.com/albums/a1...k/e1363d09.jpg
New poster! (less than 10 posts)
Very very impressive, Mark! I am still trying to get my jaw off the floor!
Brilliant! I feel like inventing a new word - what about insanilicious? hmm, yep that is definately the right word...
Keep posting:cool:
finally got my oil cooler leak free tonite :agree: 60psi oil pressure when cold now, can't be bad :smokin:
all fits behind the grille too which is lucky, i was worried for a minute.. :ashamed:
http://i11.photobucket.com/albums/a1...k/5eb08f82.jpg
http://i11.photobucket.com/albums/a1...k/b4cfed94.jpg
engine bay almost back together, just ordering a couple of new pipes to replace some crappy ones
http://i11.photobucket.com/albums/a1...k/112ce8e6.jpg
http://i11.photobucket.com/albums/a1...k/8c974dc0.jpg
still got lots to do, but its getting there :D:D:D
grrr still leaked even wit new sanwich plate and seal, big thank u to lill bro jimmy_b for having enthusiasm to fix it finally. really do have no leaks now :-)
few more update pics
finally leak free!!
http://i11.photobucket.com/albums/a1...k/a915767e.jpg
painted brakes to match calipers now
http://i11.photobucket.com/albums/a1...k/10b26d4f.jpg
cheeky one of bro's new 182 fitting his £130 cup splitter :eek:
http://i11.photobucket.com/albums/a1...k/4e7adedc.jpg
almost back together, and my other halves KA which drove up there tonight as a 1.3 and will drive away as a 1.8 zetec (one MY car is done :laugh:) already got the sportka bumper on to check the fit
http://i11.photobucket.com/albums/a1...k/40679a4c.jpg
been slightly distracted lately as i now have 3 cars on the go... the ka has its zetec heart, and i'm currently restoring the 'barn find' to its former OE glory, so poor old ginger has taken a back seat once again
finally making my gauge pod up
http://i11.photobucket.com/albums/a1...k/ca34e671.jpg
http://i11.photobucket.com/albums/a1...k/2b67f86d.jpg
and a couple of shots from the weekend of oli's and the barn find in the unit
http://i11.photobucket.com/albums/a1...k/eab87018.jpg
http://i11.photobucket.com/albums/a1...k/bb27c350.jpg
and u can see ginger hiding in the background! 4x r5's in one place! (black ph2 is behind the ka :smokin:)
http://i11.photobucket.com/albums/a1...k/b0926cd6.jpg
http://i11.photobucket.com/albums/a1...k/b0926cd6.jpg
That unit looks fooking handy, how did you go about finding that.......
Would love to have space like that, a bit over working in a tiny garage:mad:
How's the donkey? :laugh:
:laugh:
tonites orange car progress was flocked dashtop and gauges back in :smokin:
http://i11.photobucket.com/albums/a1...k/0c6744fa.jpg
the weekends events... sat cleaned it up, sat eve blew it up :laugh:
sunday ripped it apart, liner cracked between 1 and 2 :disagree:
Not good matey sounds like you may have a det problem as your are running high comp so you are much closer to the threshold. What max boost do you run nowadays? and do you use the water injection to help reduce the det?
2bar is a lot of boost, to crack a liner she must have been knocking a fair bit/fuelling leaned out...classic carb bowl emptying on a long pull?? Get a steth on when u get it back together to listen for det.
was flat out for about 10sec max, probably less, afr's looked ok in the corner of my eye but its hard to check them when your concentrating on driving :laugh:
here are some pics from yesterday, didn't get too many as i was hands on all day
https://www.rtoc.org/boards/picture.p...ictureid=15775
https://www.rtoc.org/boards/picture.p...ictureid=15776
https://www.rtoc.org/boards/picture.p...ictureid=15777
https://www.rtoc.org/boards/picture.p...ictureid=15778
https://www.rtoc.org/boards/picture.p...ictureid=15779
https://www.rtoc.org/boards/picture.p...ictureid=15780
https://www.rtoc.org/boards/picture.p...ictureid=15781
https://www.rtoc.org/boards/picture.p...ictureid=15782
https://www.rtoc.org/boards/picture.p...ictureid=15783
new rings and gaskets on order, need new liner machined down by 0.75 then that can go in. also going to sort another clutch as the volvo 440 ones only seem to last a few minutes before they slip in 5th :(
last nights progress.... found this :disagree:
https://www.rtoc.org/boards/picture.p...ictureid=15788
https://www.rtoc.org/boards/picture.p...ictureid=15789
so got on with this:
https://www.rtoc.org/boards/picture.p...ictureid=15790
and a box of bits to powder coat :)
https://www.rtoc.org/boards/picture.p...ictureid=15792
and my organised mess :scratch:
https://www.rtoc.org/boards/picture.p...ictureid=15793
Mark, that doesn't look good damage looks like over speeding and high boost damage to the piston to cause that maybe a weak mixture in that cylinder.
i was going to say what would cause the ringlands to go like that.. AFR's were ok as far as i know, i use an AEM UEGO, but like i said earlier its hard to concentrate on driving on a country road at the best of times :laugh:
i think it may be boosting slightly higher with the tubular on, or should i say spiking higher, i didn't really check. that piston has been in there ages, and the liner since my pod 'pop' in 2008, tbh i just threw it together last time with the old rings on new liner etc. it was cyl one that went, it had been breathing heavily for a while as well, usually on high boost, to the point where its ruined my clutch by blowing oil down past the TDC sensor :disagree:
I found when I used the gaytec Mk1 manifold that boost level stayed the same but the spool up was quicker 200rpm's quicker (i got rid purely as I missed the burble). Afr's may have been ok on the gauge Mark, but the readings are taken in the downpipe so once out of the engine. The inlet manifold is a bad design and cylinders 1 & 4 run leaner than 2&3.
Quick off topic question with your VNT and high comp engine what is the location of your TDC sensor? are you running fully retarded or advance?
Breathing heavy could also be part problem may have had lack of lubrication for the pistons:scratch:.
my TDC sensor is really far back (towards bulkhead) if that helps?! its how mike set it up
the piston damage is from detonation, be it caused by weak fueling or too much boost and ignition timing
Alot of skylines suffer the same thing when they have been hack mapped with safc2's :laugh: