-
Piper 285 + Matched followers
As above, must not be a re-grind and followers must be kept in order with the cam, vernier not essential but a plus.
What have you???
-
Re: Piper 285 + Matched followers
http://www.motorsportworld.co.uk/det...-BL&PID=318470
I sourced my cam kit, cam/springs/pully through these guys, it wasn't a re-grind and to my suprise when I installed it, it timed up @ 112 degrees:eek:
As for followers I used some that had be checked for wear (concave faces) and used the flatest ones I could find. My engine hasn't been apart since so as for being able to comment on the longevity of my cam lobes I can't and my motor only made 209hp @24 psi and I'm still non the wiser for why. I hope the followers I used haven't done similar to my shiney new camshaft........
If your willing to fork out then new followers are the best bet imo;)
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
GTphil
http://www.motorsportworld.co.uk/det...-BL&PID=318470
I sourced my cam kit, cam/springs/pully through these guys, it wasn't a re-grind and to my suprise when I installed it, it timed up @ 112 degrees:eek:
As for followers I used some that had be checked for wear (concave faces) and used the flatest ones I could find. My engine hasn't been apart since so as for being able to comment on the longevity of my cam lobes I can't and my motor only made 209hp @24 psi and I'm still non the wiser for why. I hope the followers I used haven't done similar to my shiney new camshaft........
If your willing to fork out then new followers are the best bet imo;)
Cheers for that Phil - I remember yours at Scoff's RR, you did quite well - what turbo are you running? and If I remember rightly yours pulled hard to 7k+, Mine starts dropping orf at 6.5k, so if I were you, I'd be a happy bunny.
-
Re: Piper 285 + Matched followers
Actually it peaked at 6.5k but then began to tail off slightly hence my slight reason for concern. Looking at your thread you mentioned that yours was a little tappy, mine are set to pipers recomendations and it's quiet as a mouse.
anyways this is of no use to you getting the parts your after so I will stop mucking up your add .....:laugh:
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
GTphil
Actually it peaked at 6.5k but then began to tail off slightly hence my slight reason for concern. Looking at your thread you mentioned that yours was a little tappy, mine are set to pipers recomendations and it's quiet as a mouse.
anyways this is of no use to you getting the parts your after so I will stop mucking up your add .....:laugh:
LOL, don't worry about it. I think I'm going to Have to bite the bullet and buy new cam and followers. :cry:
-
Re: Piper 285 + Matched followers
Why not just get a good second hand set and get them refaced and re-hardend?
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Dave Reed
Why not just get a good second hand set and get them refaced and re-hardend?
:agree: Thats what was done to mine many years ago.
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Dave Reed
Why not just get a good second hand set and get them refaced and re-hardend?
What hardening did you get done?
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Big Steve - Raider
What hardening did you get done?
I think it's called case hardening, although I'd have to check.. My engine builder sorted it tbh :)
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Dave Reed
I think it's called case hardening, although I'd have to check.. My engine builder sorted it tbh :)
Super :niceone:
That's the ticket Dave, heard of Case Hardening before, i'll look into that myself! ;)
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Big Steve - Raider
Super :niceone:
That's the ticket Dave, heard of Case Hardening before, i'll look into that myself! ;)
Any good engineering place should be able to help you out..
-
Re: Piper 285 + Matched followers
I thought the idea of new followers where all about them not being uber hard to begin with then, them toughening up within the run-in period??
Or am I talking out of my arse as usual?
-
Re: Piper 285 + Matched followers
Where did you get yours done Logg
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
TNT ANDY
Where did you get yours done Logg
My mate built my engine all my bit's would of been sent off with his work stuff I think they use H. T. Howard. As Dave have said I guess most engineering shops should be able to help you.
-
Re: Piper 285 + Matched followers
Cheers buddy - I've just been speaking to a chap who lives not 3 miles from here who does a lot of engineering stuff. I'l go see him on Saturday AM
:agree:
-
Re: Piper 285 + Matched followers
:D an engineer that does engineering stuff :wasntme:
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Tony Walker
:D an engineer that does engineering stuff :wasntme:
:laugh: yeah, you don't want one of those Engineer's that does Baking, or a Vet who does engineering stuff :wasntme:
-
Re: Piper 285 + Matched followers
Just spotted H. T. Howard have a website probably no help as they're so far away. But can always ask them some questions.
http://www.hthoward.co.uk/
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Logg
Just spotted H. T. Howard have a website probably no help as they're so far away. But can always ask them some questions.
http://www.hthoward.co.uk/
:agree::agree::agree:
-
Re: Piper 285 + Matched followers
Steve / Tony - Are you on drugs:laugh::wasntme:
-
Re: Piper 285 + Matched followers
:eek: how dare u lol just bud :agree:
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Tony Walker
:eek: how dare u lol just bud :agree:
:laugh::laugh::laugh::laugh:
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
TNT ANDY
I thought the idea of new followers where all about them not being uber hard to begin with then, them toughening up within the run-in period??
Or am I talking out of my arse as usual?
Think it's more to do with the original followers becoming ovallated (if that's a word) and the contact surface becoming dished. The tips of the new cams are thinner and the shallow end lowered which brings the tip of the cam closer to the edge of the follower, before the dish caused by old cam, effectively leaving a lip which needs to be worn down before full contact is achieved on full rotation (the follower isn't in contact with the cam for a micro second allowing the cam and follower to hit, same way as a cylinder mower cuts is the only example that comes to mind ).
A straight edge across the top and digi micrometers will show signs of wear
-
Re: Piper 285 + Matched followers
Surprised no-one's ever looked into getting these made? They're only a 'bucket' with a hardened face after all. Surely they can be produced & supplied for cheaper than the £16 (*) per follower that Renault charge?
* Or that's the price they were around 8 years ago anyway.
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Mart
Surprised no-one's ever looked into getting these made? They're only a 'bucket' with a hardened face after all. Surely they can be produced & supplied for cheaper than the £16 (*) per follower that Renault charge?
* Or that's the price they were around 8 years ago anyway.
I'd be interested in a set if anyone was looking into it..?
They're £19 each or so now! :eek:
-
Re: Piper 285 + Matched followers
It is a bit bonkers really.
For those who had there's re-worked - How much did it cost?
-
Re: Piper 285 + Matched followers
There's two sizes as well. Not sure what they are but It's something like 1 or 2 mm difference in diameter. I'd look into having the block bored out to remove any wear and start from fresh with the larger size, not sure if that would be possibl though e.
Measuring your old ones is fun as due to them becoming ovalled you have no idea which size you need, I gave up and chucked the old ones back in as only had a mild reprofile and never had any issue with the cam ect.
-
Re: Piper 285 + Matched followers
19mm & 19.2mm rings a bell.
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Mart
19mm & 19.2mm rings a bell.
:agree:
Mine are 19mm.
Been in contact with catcams, they recommend new followers but also say they can clean up and refinish them for £10.00 + vat each, so £12.00 each.
For £54.00 I think I'll stick new in.
-
Re: Piper 285 + Matched followers
Got the Cam out tonight - looks a bit poo!
http://www.facebook.com/media/set/?s...3975552&type=1
Let me know if you can't see these.
-
Re: Piper 285 + Matched followers
mine was similar apart from that one lobe thats worn flat.was it a billet or regrind before it went in? how many miles has it done?
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Tony Walker
mine was similar apart from that one lobe thats worn flat.was it a billet or regrind before it went in? how many miles has it done?
It was a regrind, and I'd say about 15K of hard miles. Not good really. I've never used top brand oil, always semi synthetic. Might be something in that?
-
Re: Piper 285 + Matched followers
difficult to say :S if it had been starved of oil it would be like that within a few hundered miles. Quality of oil? :S maybe... id say thats more critical for the turbo, have you screwed any turbos?
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
Tony Walker
difficult to say :S if it had been starved of oil it would be like that within a few hundered miles. Quality of oil? :S maybe... id say thats more critical for the turbo, have you screwed any turbos?
No - Turbo's have been fine. I'll be using a quality oil from now on, So I suppose stick a new cam in and away we go.
-
Re: Piper 285 + Matched followers
CatCams 285 ordered
Of to Renault today for a spanking.:cry:
-
Re: Piper 285 + Matched followers
Ordered Followers:)
£24 each + vat:eek:
Haggled down to £19 each + Vat
Might have some interest from Renault for Sangliers.:agree:
-
Re: Piper 285 + Matched followers
I could have helped with these.
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
phase i 16 v turbo
I could have helped with these.
Oh dear
-
Re: Piper 285 + Matched followers
I have a piper account and have followers new and refurbished :agree:
-
Re: Piper 285 + Matched followers
Where where you when I needed you LOL. Please don't post up the prices:(
-
Re: Piper 285 + Matched followers
Quote:
Originally Posted by
TNT ANDY
Ordered Followers:)
Haggled down to £19 each + vat
sore one :sad2: